Honeywell RTH230B handleiding

Honeywell RTH230B
9.2 · 2
PDF handleiding
 · 4 pagina's
Engels
handleidingHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

Bekijk hier gratis de handleiding van de Honeywell RTH230B. Deze handleiding valt onder de categorie thermostaten en is door 2 mensen gewaardeerd met een gemiddelde van een 9.2. Deze handleiding is beschikbaar in de volgende talen: Engels. Heeft u een vraag over de Honeywell RTH230B of heeft u hulp nodig? Stel hier je vraag

Hulp nodig?

Heb je een vraag over de Honeywell en staat het antwoord niet in de handleiding?

  • Ontvang updates bij oplossingen
  • Krijg antwoord op je vraag

Vraag en antwoord

Aantal vragen: 0

De Honeywell RTH230B is een thermostaat die ontworpen is om de temperatuur in huis nauwkeurig te regelen. Met zijn eenvoudige en gebruiksvriendelijke ontwerp maakt deze thermostaat het gemakkelijk om de gewenste temperatuur in te stellen en te behouden. De Honeywell RTH230B beschikt over een programmeerbare functie, waardoor gebruikers verschillende temperaturen kunnen instellen voor verschillende tijden van de dag. Dit helpt om energie te besparen door automatisch de temperatuur aan te passen wanneer er niemand thuis is of wanneer iedereen slaapt. De thermostaat heeft een groot display dat duidelijk de huidige temperatuur en andere informatie weergeeft. Met de knoppen aan de zijkant van het apparaat kunnen gebruikers eenvoudig de gewenste temperatuur aanpassen. De Honeywell RTH230B is compatibel met de meeste standaard verwarmingssystemen, waaronder gas, elektriciteit en olie. Het kan ook worden gebruikt in woningen met een warmtepomp-systeem. Met zijn betrouwbare prestaties en duurzaamheid is de Honeywell RTH230B een ideale keuze voor iedereen die op zoek is naar een eenvoudige en efficiënte thermostaat. Het zorgt voor een comfortabele temperatuur in huis en helpt tegelijkertijd om energie te besparen.

Algemeen
MerkHoneywell
ModelRTH230B
Productthermostaat
TaalEngels
BestandstypeHandleiding (PDF)

Het antwoord op uw vraag niet in de handleiding kunnen vinden? Wellicht staat het antwoord op uw vraag hieronder in de meest gestelde vragen over de Honeywell RTH230B.

Waar kan ik de thermostaat het beste plaatsen?

De beste plaats voor de thermostaat is de ruimte waar u het meest verblijft, in veel gevallen de woonkamer of keuken. Plaats de thermostaat zo'n anderhalve meter boven de vloer, niet in de zon te hangen en niet op een buitenmuur.

Wat is een dode zone van een thermostaat?

Bij een dode zone van uw thermostaat is uw installatie als het ware ‘in rust’. De thermostaat schakelt pas in wanneer het verschil bijvoorbeeld meer dan 2˚C afwijkt van de ingestelde kamertemperatuur.

Wat is de ideale kamertemperatuur?

De meeste mensen vinden dat de ideale kamertemperatuur tussen de 19 en 22 graden Celsius ligt.

Is de handleiding van de Honeywell RTH230B in het Nederlands beschikbaar?

Helaas hebben we de handleiding van de Honeywell RTH230B niet beschikbaar in het Nederlands. Deze handleiding is wel beschikbaar in het Engels.

Staat je vraag er niet tussen? Stel hier je vraag

Geen resultaten