Fujitsu MBA3300NP handleiding

Fujitsu MBA3300NP
(1)
  • Aantal pagina's: 2
  • Bestandstype: PDF
  • CARE OF YOUR FUJITSU HARD DISK DRIVE (HDD)
    Careful handling and installation of your HDD is paramount to the longevity of the unit. The internal mechanism of the HDD can be
    seriously damaged if the HDD is subjected to forces outside the environmental specifications. When transporting the HDD, always use the
    original packaging in which the HDD was delivered to you, and avoid exposing the HDD to extreme changes in temperature to minimize the
    risk of condensation.
    Handling
    1. Never drop the unit. Handle it with care.
    2. Never move the HDD while the disks are spinning. Note that the disks spin when the HDD is powered on and also immediately after
    power off. Refer to the Start/Stop specification for your HDD.
    3. Always turn off the power before connecting or disconnecting the interface cable. The same applies to changing any of the switches or
    terminal settings except Write protect switch on NP model drives.
    4. Never place the HDD in the vicinity of equipment giving off strong magnetic fields, such as CRT monitors, televisions, or loudspeakers.
    5. Never use any cleaning agents or liquids on the HDD.
    6. Always use an antistatic mat and wrist strap when handling the HDD. Hold the HDD by the base casting and never touch the components
    on printed circuit board assembly.
    7. Never remove any labels from the HDD or deface them in any way.
    8. Never open the HDD for any reason. Doing so will void any warranties.
    9. Always pay close attention to the mounting specifications such as those for sway space and cooling. If the temperature difference
    between the storage location and installation locations exceeds 10°C, for temperature acclimation purposes, leave the HDD in the new
    location for at least two hours before turning it on. This minimizes any risk of condensation forming on the HDD.
    The HDD needs NO preventative or periodic maintenance during its service life if properly used in the appropriate environment.
    INSTALLATION
    1. ORIENTATION–The HDD can be installed flat on any of its six sides. Inclination from vertical or horizontal plane should not exceed
    5
    °.
    2. MOUNTING SCREW INSTALLATION–When the mounting screw holes on the side of the HDD are used, be sure to use the two pairs
    of outer holes. Do not use the center hole in conjunction with only one of the outer holes. The screws must not penetrate the HDD by more
    than 5.0 millimeters. Impact caused by the electric screwdriver must be within the HDD specifications.
    3. COOLING–Allow space above and below the HDD to provide an adequate air flow. Fan cooling is recommended. The HDD
    temperature measured at center of top cover (label side) should never exceed 60°C. See Table 1.
    Table 1. Reference value of airflow
    Environmental temperature Required velocity of airflow
    30
    °C > 0.3m/s
    35°C > 0.6 m/s
    40°C > 0.9 m/s
    45°C > 1.5 m/s
    4. TERMINATION–A terminator should be installed externally at both ends of the SCSI bus.
    5. TERMINATOR POWER–Terminator power must be supplied to terminator for correct operation. This can be supplied from either the
    HDD, except for NC model or the SCSI bus. If only NC models are connected to the SCCI bus, terminator power should be supplied
    externally.
    6. CONNECTING–To avoid potential damage to the HDD, make sure that connector type and orientation is correct.
    CAUTION: Your warranty may be voided if the connector is damaged as a result of incorrect insertion.

    MBA3300NC, MBA3300NP, MBA3147NC, MBA3147NP,

    MBA3073NC, MBA3073NP

    HARD DISK DRIVES INSTALLATION GUIDE

    FUJITSU LIMITED
    Storage Products Group
    4-1-1 Kamikodanaka, Nakahara-ku, Kawasaki 211-8588, Kanagawa-ken, Japan
    Copyright © 2007 FUJITSU LIMITED

    C141-E271-01EN

    http://www.fujitsu.com/
    Undermentioned information is effective only in EU for traceability of the EMC Directive
    Manufacturer:
    Fujitsu Limited
    4-1-1 Kamikodanaka, Nakahara-ku, Kawasaki 211-8588, Kanagawa-ken, Japan
    Authorized representative importer / distributor in EU:
    Fujitsu Europe Limited
    Ha
    y
    es Park Central, Ha
    y
    es End Road, Ha
    y
    es, Middlesex, UB4 8FE, United Kin
    g
    dom
Fujitsu MBA3300NP

Hulp nodig?

Aantal vragen: 0

Heeft u een vraag over de Fujitsu MBA3300NP of heeft u hulp nodig? Stel hier je vraag. Zorg voor een duidelijke en uitgebreide omschrijving van het probleem en je vraag. Hoe beter je probleem en vraag is omschreven, hoe makkelijker het is voor andere Fujitsu MBA3300NP bezitters om je van een goed antwoord te voorzien.

Bekijk hier gratis de handleiding van de Fujitsu MBA3300NP. Deze handleiding valt onder de categorie Harde schijven en is door 1 mensen gewaardeerd met een gemiddelde van een 7.5. Deze handleiding is beschikbaar in de volgende talen: Engels. Heeft u een vraag over de Fujitsu MBA3300NP of heeft u hulp nodig? Stel hier je vraag

Fujitsu MBA3300NP specificaties

Algemeen
Merk Fujitsu
Model MBA3300NP
Product Harde schijf
Taal Engels
Bestandstype PDF
Kenmerken
HDD capaciteit 300 GB
HDD rotatiesnelheid 15000 RPM
Interface SATA
HDD omvang 3.5 "
Gemiddelde wachttijd 2.00 ms
Track to track zoektijd 0.2 ms
Buffergrootte opslagstation 16 MB
Full stroke seek time 8 ms
Gemiddelde zoektijd 3.4 ms
Mean time between failures (MTBF) 1400000 uur
Overige specificaties
Intern Ja
Afmetingen (BxDxH) 101.6 x 143 x 25.4 mm
Gewicht en omvang
Gewicht 750 g
Diepte 146 mm
Hoogte 25.4 mm
Breedte 101.6 mm
Eisen aan de omgeving
Schokbestendigheid 65 G
Temperatuur, in bedrijf 5 - 55 °C
Temperatuur bij opslag -40 - 70 °C
Relatieve luchtvochtigheid, in bedrijf 5 - 95 procent
Luchtvochtigheid bij opslag 5 - 95 procent
Hoogte, in bedrijf 0 - 3000 m
Hoogte bij opslag 0 - 12000 m
Schokbestendigheid (buiten gebruik) 250 G
Trillingen, in bedrijf 0.6mm (5 - 20 Hz)/ 1.0G (20 - 300 Hz) G
Trillingen bij opslag 3.1mm (5 - 20 Hz)/ 5.0G (20 - 300Hz) G
Energie
Typisch stroomverbruik 12.8 W
Operating voltage 5 / 12 V
toon meer

Veelgestelde vragen

Hieronder vindt u de meest gestelde vragen over de Fujitsu MBA3300NP.

Staat je vraag er niet tussen? Stel hier je vraag