Fujitsu MAW 3300 NP handleiding

Fujitsu MAW 3300 NP
(1)
  • Aantal pagina's: 2
  • Bestandstype: PDF
  • MAW3300NC/NP, MAW3147NC/NP,

    MAW3073NC/NP

    DISK DRIVES INSTALLATION GUIDE

    CARE OF YOUR FUJITSU DRIVE
    Careful handling and installation of your disk drive is paramount to the longevity of the unit. Serious damage can occur to the internal
    mechanisms if forces outside the environmental specifications are exerted to the casing. In transportation, always use the original packing
    in which the drive was supplied and avoid sharp changes in temperature to minimise the risk of condensation.
    Handling
    1. Never drop. Handle with care.
    2. Never move the disk drive while the disks are spinning. This is when the drive is powered on and also immediately after power off.
    Refer to the Start/Stop specification for your drive.
    3. Always turn off the power before connecting or disconnecting the interface cable. The same applies to changing any of the switches or
    terminal settings except Write protect switch on NP model drives.
    4. Never place the drive in the vicinity of strong magnetic fields such as monitors, televisions, or loudspeakers.
    5. Never use any cleaning agents or liquids on the drive.
    6. Always use an antistatic mat and wrist strap when handling the drive. Hold the drive by the Base casting and never touch the components
    on printed circuit board.
    7. Never remove any labels from the drive and do not deface them in any way; these labels are part of the disk drive design.
    8. Never open the disk enclosure for any reason. Doing so voids any warranty.
    9. Always pay close attention to the mounting specifications such as sway space and cooling. If the temperature difference between storage
    location and installation locations is more than 10°C, leave the drive in the new location for at least two hours for Temperature acclimation.
    This minimises any risk of condensation forming on the drive.
    The Drive needs NO preventative or periodic maintenance during its life time if properly used in the correct environment.
    INSTALLATION
    1. ORIENTATION–The drive can be installed in each six surface down orientations. Inclination from vertical or horizontal should not
    exceed 5
    °.
    2. MOUNTING SCREW INSTALLATION–When the mounting screw holes on the side of the drive are used, be sure to use the two pairs
    of outer holes. Do not use the center hole in conjunction with only one of the outer holes. The screws must not penetrate the drive by more
    than 5.0 millimeters. Impact caused by the electric driver must be within the device specifications.
    3. COOLING–Allow space above and below the drive to provide an adequate air flow. Fan cooling is recommended. The disk enclosure
    temperature measured at center of base cover (label side) should never exceed 60°C. See Table 1.
    Table 1. Reference value of airflow
    Environmental temperature Required velocity of airflow
    35
    °C > 0.2m/s
    40
    °C > 0.5 m/s
    45°C > 0.9 m/s
    50°C > 1.5 m/s
    4. TERMINATION–A terminator should be installed externally at both ends of the SCSI bus.
    5. TERMINATOR POWER–Terminator power must be supplied to terminator for correct operation. This can be supplied from either the
    drive, except for NC model or the SCSI bus. If only NC model drives are connected to the SCCI bus, terminator power should be supplied
    externally.
    6. ATTACHING THE CABLES–To avoid possible damage to the drive, make sure the direction of the connector matches.
    CAUTION: Warranty may be avoided if damage to the connector is caused by wrong insertion.
    FUJITSU LIMITED
    Storage Products Group
    4-1-1 Kamikodanaka, Nakahara-ku, Kawasaki 211-8588, Kanagawa-ken, Japan
    Copyright © 2005 FUJITSU LIMITED
    Corporate http://www.jp.fujitsu.com/
    USA http://www.fcpa.com/
    EUROPE http://www.fujitsu-europe.com/

    C141-E227-01EN

Fujitsu MAW 3300 NP

Hulp nodig?

Aantal vragen: 0

Heeft u een vraag over de Fujitsu MAW 3300 NP of heeft u hulp nodig? Stel hier je vraag. Zorg voor een duidelijke en uitgebreide omschrijving van het probleem en je vraag. Hoe beter je probleem en vraag is omschreven, hoe makkelijker het is voor andere Fujitsu MAW 3300 NP bezitters om je van een goed antwoord te voorzien.

Bekijk hier gratis de handleiding van de Fujitsu MAW 3300 NP. Deze handleiding valt onder de categorie Harde schijven en is door 1 mensen gewaardeerd met een gemiddelde van een 7.5. Deze handleiding is beschikbaar in de volgende talen: Engels. Heeft u een vraag over de Fujitsu MAW 3300 NP of heeft u hulp nodig? Stel hier je vraag

Fujitsu MAW 3300 NP specificaties

Algemeen
Merk Fujitsu
Model MAW 3300 NP
Product Harde schijf
Taal Engels
Bestandstype PDF
Kenmerken
HDD capaciteit 300 GB
Gemiddelde wachttijd 2.99 ms
Track to track zoektijd 0.2 ms
Interface Ultra320 SCSI
Buffergrootte opslagstation 8 MB
Full stroke seek time 10 ms
Gemiddelde zoektijd 4.5 ms
Mean time between failures (MTBF) 1200000 uur
Overige specificaties
Intern Ja
Afmetingen (BxDxH) 101.6 x 143 x 25.4 mm
Gewicht en omvang
Gewicht 750 g
Diepte 146 mm
Hoogte 25.4 mm
Breedte 101.6 mm
Eisen aan de omgeving
Schokbestendigheid 65 G
Temperatuur, in bedrijf 5 - 55 °C
Temperatuur bij opslag -40 - 70 °C
Relatieve luchtvochtigheid, in bedrijf 5 - 95 procent
Luchtvochtigheid bij opslag 5 - 95 procent
Hoogte, in bedrijf 0 - 3000 m
Hoogte bij opslag 0 - 12000 m
Schokbestendigheid (buiten gebruik) 225 G
Trillingen, in bedrijf 0.6mm (5 - 20 Hz)/ 1.0G (20 - 300 Hz) G
Energie
Typisch stroomverbruik 9.5 W
toon meer

Veelgestelde vragen

Hieronder vindt u de meest gestelde vragen over de Fujitsu MAW 3300 NP.

Staat je vraag er niet tussen? Stel hier je vraag