Barracuda Networks Message Archiver 450 handleiding

Barracuda Networks Message Archiver 450
(1)
  • Aantal pagina's: 2
  • Bestandstype: PDF
  • Message Archiver

    Barracuda Message Archiver - Quick Start Guide

    The Barracuda Message Archiver is a message archiving appliance that ensures all
    messages entering and leaving your network, along with inter-company emails, are
    archived and available for searching without the need for quotas on your email server.
    It is common for the Barracuda Message Archiver to be physically installed on your
    network and assigned an IP address as a node on your internal network.
    Getting Started
    This guide provides you with setup instructions for the Barracuda Message
    Archiver. We recommend reading these instructions fully before starting the
    setup. To begin setting up your Barracuda Message Archiver, you will need the
    following:
    Barracuda Message Archiver, AC power cord, ethernet cables (included)
    VGA monitor (recommended)
    PS2 keyboard (recommended)
    Physical Installation
    To install the Barracuda Message Archiver:
    1. Fasten the Barracuda Message Archiver to a 19-inch rack or place it in a
    stable location.
    2. Connect an ethernet cable from your network switch to the ethernet port on
    the back of the Barracuda Message Archiver.
    3. Connect a standard VGA monitor, PS2 keyboard, and an AC power cord to
    the Barracuda Message Archiver. Note: Immediately after connecting an
    AC power cord to the unit, it may power ON for a few seconds and then
    power OFF. This is because the unit is designed to automatically return to
    a powered ON state in the event of a power outage.
    4. Press the POWER button on the front panel to turn the unit on.
    Configure IP Address and Network Settings
    If you have a monitor connected, the Barracuda Message Archiver will display
    the Boot Menu initially, and the Administrative Console login prompt once fully
    booted. To begin the configuration:
    1. Login to the Administrative Console using the admin login:
    1. Login: admin
    2. Password: admin
    2. Configure the IP Address, Subnet Mask, Default Gateway, Primary DNS
    Server and Secondary DNS Server as appropriate for your network.
    3. Save your changes.
    If you do not have a monitor and keyboard and want to set the IP using the
    RESET button on the front panel, press and hold the RESET button per the
    following table:
    IP address Press and hold RESET for
    192.168.200.200 5 seconds
    192.168.1.200 8 seconds
    10.1.1.200 12 seconds
    Open Firewall Ports
    If your Barracuda Message Archiver is located behind a corporate firewall, open
    the following ports on your firewall to ensure proper operation.
    Port Direction TCP UDP Usage
    22 In/Out Yes No Remote diagnostics and service (recommended)*
    25 In/Out Yes No Email and email bounces
    53 Out Yes Yes Domain Name Service (DNS)
    80 Out Yes No Virus, Policy and Document Definition updates
    123 In/Out No Yes Network Time Protocol (NTP)
    *Access via Port 22 is required only if Technical Support is requested.
    Verify and Configure Access from the Web Interface
    Use a computer with a Web browser that is connected to the same network as
    the Barracuda and follow these steps:
    1. In the browser address bar, enter http:// followed by the IP address of the
    Barracuda, followed by the default Web Interface HTTP Port (:8000). For
    example, if you configured the Barracuda with an IP address of
    192.168.200.200, you would enter the following:
    http://192.168.200.200:8000
    2. Log in to the Barracuda Message Archiver Web interface as the
    administrator:
    Username: admin Password: admin
    3. Go to the BasicÆ IP Configuration page and perform the following:
    Verify the values for IP Address, Subnet Mask, and Default Gateway.
    Verify the values for Primary and Secondary DNS Server.
    Enter the Default Hostname and Default Domain. This is the name that
    will be associated with bounced messages. For example, enter
    barracuda as the Default Hostname and <yourdomainname>.com as
    the Default Domain.
    In the Local Domains section, enter the email domains that are to be
    archived. Click Add after each domain entry.
    4. Click any one of the Save Changes buttons to save all of the information.
Barracuda Networks Message Archiver 450

Hulp nodig?

Aantal vragen: 0

Heeft u een vraag over de Barracuda Networks Message Archiver 450 of heeft u hulp nodig? Stel hier je vraag. Zorg voor een duidelijke en uitgebreide omschrijving van het probleem en je vraag. Hoe beter je probleem en vraag is omschreven, hoe makkelijker het is voor andere Barracuda Networks Message Archiver 450 bezitters om je van een goed antwoord te voorzien.

Bekijk hier gratis de handleiding van de Barracuda Networks Message Archiver 450. Deze handleiding valt onder de categorie Servers en is door 1 mensen gewaardeerd met een gemiddelde van een 9.3. Deze handleiding is beschikbaar in de volgende talen: Engels. Heeft u een vraag over de Barracuda Networks Message Archiver 450 of heeft u hulp nodig? Stel hier je vraag

Barracuda Networks Message Archiver 450 specificaties

Algemeen
Merk Barracuda Networks
Model Message Archiver 450
Product Server
Taal Engels
Bestandstype PDF
Opslagmedia
Totale geïnstalleerde opslagcapaciteit 1 TB
Soorten RAID 1
Poorten & interfaces
Aantal Ethernet LAN (RJ-45)-poorten 1
Seriële poort(en) 1
Prestatie
Aantal gebruikers 1000 gebruiker(s)
Overige specificaties
Afmetingen (BxDxH) 437 x 503 x 43 mm
Connectivity LEDs Ja
Link/Act LED Ja
Aansluitingen VGA, PS/2
Stroomvoorziening 100 - 240 VAC, 50/60 Hz
Design
Type behuizing Rack (1U)
Gewicht en omvang
Gewicht 9500 g

Veelgestelde vragen

Hieronder vindt u de meest gestelde vragen over de Barracuda Networks Message Archiver 450.

Staat je vraag er niet tussen? Stel hier je vraag