Atdec SD-AT-DK-P handleiding

Atdec SD-AT-DK-P
(1)
  • Aantal pagina's: 2
  • Bestandstype: PDF
  • Component Checklist

    Installation Instructions

    SPACEDEC ACROBAT

    ARTICULATED ARM

    Single Arm
    Articulated Arm
    Assembly (x1)
    Base Casting (x1)
    Cable Wrap
    Applicator (x1)
    Top Cap Tool (x1)
    2.5mm Allen
    Key (x1)
    16mm Cable
    Wrap (x1)
    M10 Interscrew (x1)
    Cable Clip (x4)
    M6x12mm
    Countersunk
    Screw (x2)
    Extension
    Clip (x4)
    Desk Clamp Box
    Desk Clamp
    Bracket (x1)
    M8 Desk Clamp
    Screw (x2)
    Pressure
    Plate (x2)
    Component Checklist
    A
    Check you have received all parts against the Component Checklist above.
    Bits Box
    5mm Allen
    Key (x1)
    Assembling the Arm
    B
    Adjusting the Display
    H
    As LCD Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the mounting hole pattern does not comply with the
    international VESA standards. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice.
    Published: 12.04.07
    Installation Complete
    14 Gauge Self
    Tapping Screw (x2)
    B.1. Disassemble the Tube Assembly
    In order to attach the Articulated Arm to the
    tube assembly you will need to remove the
    Top Cap and Threaded Rod as shown:
    B.2. Assemble the Articulated Arm
    Assemble the Articulated Arm as shown:
    Top Cap and
    Threaded Rod
    Arm Assembly
    Internal Tube Post
    Spacer
    Tube
    Top Cap and
    Threaded Rod
    Internal
    Tube Post
    Spacer
    Tube
    Collar
    Mounting Fasteners
    M4x10mm
    Screw (x4)
    M4x12mm
    Screw (x4)
    M4x16mm
    Screw (x4)
    Tube Assembly (x1)
    Threaded Rod
    and Top Cap (x1)
    Collar
    Inner Tube Post
    Spacer Tube
    Washer (x1)
    H.1. Adjusting the Ball Joint Resistance
    The Acrobat Articulated Arm comes factory set to support 6kg displays. Adjust the arm to suit the weight of your
    display as shown in the following steps:
    Depending on the weight of the monitor, it may
    be necessary to make adjustments to the Ball Joint
    Mechanism. If the monitor doesn’t hold its position or
    is too resistant, adjust the four tension screws located
    around the Ball Joint (see diagram on the right) using
    the supplied 2.5mm Allen Key.
    Check the display, and then adjust again if necessary.
    NOTE: Be sure to adjust screws evenly.
    Tighten
    Loosen
    Tension
    Screws (x4)
    Ball Joint
    2.5mm
    Allen Key
    H.2. Adjusting the Pivot Head Resistance
    It is possible to control the amount of resistance in the
    Pivot Head to suit your display.
    To increase the resistant of the Pivot Head to suit heavier
    displays, use the 5mm Allen Key supplied in the Desk
    Clamp Box to tighten the interscrew in a clockwise
    direction.
    To decrease the resistance of the Pivot Head to suit
    lighter displays, loosen the interscrew in an
    anti-clockwise direction.
    NOTE: It is recommended the Pivot Head be left at the factory setting for best performance.
    Pivot Head
    Interscrew
    5mm Allen Key
    Loosen
    Tighten
    H.3. Adjusting the Articulated Arm/Gas Strut Resistance
    3kg
    Monitor
    9kg
    Monitor
    Arm
    Raise Gas
    Strut to suit
    lighter display
    5mm
    Allen key
    Gas Strut
    Lighter
    Heavier
    Lower Gas Strut to
    suit heavier display
    4mm Allen
    Key (x1)
    Ergonomic Guidelines
    G
    H.3.1. Depending on the weight of the monitor, it
    may be necessary to adjust the arm. This can be
    done by using the 5mm Allen Key supplied in the
    Desk Clamp Box.
    H.3.2. If the arm tends to automatically rise or fall
    when the display is attached, it will be necessary
    to make small adjustments to the gas strut. (see
    diagram on the right)
    H.3.3. If the arm tends to rise, the gas strut
    position should be raised. If the arm tends to fall,
    the gas strut position should be lowered.
    B
    Ergonomists recommend that the optimal position of your screen should be slightly below eye level.
    When looking at the screen’s centre the user should have a downward visual angle of approximately
    10°-20°. As a guide, the height (h) of your display should approximately be as follows:
    Tall Male (Max): 560mm (22”) Tall Female (Max): 520mm (20
    1
    /
    2)
    Short Male (Min): 368mm (14
    1
    /
    2) Short Female (Min): 356mm (14”)
    For visual comfort, a viewing distance (d) between 500mm (19
    1
    /
    2) to 750mm (29
    1
    /
    2) is
    recommended.
    Angular adjustments to reduce reflection on your monitor should range between 5° forward tilt to 15°
    backward tilt.
    Desk Clamp
    15°
    HORIZONTAL SIGHT LINE (d)
    CENTRE OF SCREEN
    10°-2
    Recommended Viewing Distance / HeightRecommended Mounting Position
    50mm (2”)
    When mounting the Spacedec Acrobat Articulated Arm, ensure the correct focal distance can be
    achieved for ultimate visual comfort (Refer to Recommended Viewing Distance / Height below)
    Desk Clamp Bolt Through
    (h)
    15mm Hole (
    9
    /
    16
    ”)
    Base Casting
Atdec SD-AT-DK-P

Hulp nodig?

Aantal vragen: 0

Heeft u een vraag over de Atdec SD-AT-DK-P of heeft u hulp nodig? Stel hier je vraag. Zorg voor een duidelijke en uitgebreide omschrijving van het probleem en je vraag. Hoe beter je probleem en vraag is omschreven, hoe makkelijker het is voor andere Atdec SD-AT-DK-P bezitters om je van een goed antwoord te voorzien.

Bekijk hier gratis de handleiding van de Atdec SD-AT-DK-P. Deze handleiding valt onder de categorie Flat panel steunen en is door 1 mensen gewaardeerd met een gemiddelde van een 9.8. Deze handleiding is beschikbaar in de volgende talen: Engels. Heeft u een vraag over de Atdec SD-AT-DK-P of heeft u hulp nodig? Stel hier je vraag

Atdec SD-AT-DK-P specificaties

Algemeen
Merk Atdec
Model SD-AT-DK-P
Product Flat panel steun
Taal Engels
Bestandstype PDF
Montage
Maximale gewichtscapaciteit 9 kg
Montagewijze Bureau
Overige specificaties
Bevestigingsstandaard VESA 75mm x 75mm / 100mm x 100mm
Lift 46 cm
Diepte 610 mm
Ergonomie
Pivot hoek 85° °
Hoek schuine stand bereik -40 - 40 °
Pan bereik -40 - 40 °
Draaihoek 360 °
Design
Kleur van het product Chroom
Gewicht en omvang
Gewicht (imperiaal) 19.8 lbs